-
About AUTOSTAR
-
-
-
-
CONTACT US
undefined
After the device power up or reboot, real-time video will appear on the display automatically. Then the device will enter and keep in pedestrian and vehicle detection mode. To make sure the normal
operation of the system, please install and calibrate the pedestrian detection alarm system carefully according to the guide of Charter 3 and Charter 5.
After reassembling the vehicle the system should be tested on the road in highway and surface street conditions. This system is capable of detecting a vehicle traveling in both directions, Passing and Overtaking.
Rear Cross Traffic Alert(RCTA) high accuracy parking ultrasonic kit buzzer alarm systemAs there are blind zone of the side mirror,driver can only see two sides of the vehicle from the side mirror,but can't see all the potential risk arounnd the vehicle,especially for the vehicles near the cab of the truck.In order to solve this problem,Autostar has developed a blind spot assist system based on microwave technology which reduce blind zone of side mirror effectively and improve the driving safety. Function:1.system self diagnosisWhen ignition key turn to "on",system start to make self diagnosis then remind driver by warning light.2.Blind spot assist function3.Rear Cross Traffic Alert(RCTA)
ParameterSpecificationItemParameterWorking voltage (V)9-36VWorking currency (mA)<300mA@12VWorking temperature(°C)-40 —— 80°CStorage temperature (°C)-40 —— 85°CWorking frequency (GHz)76GHz - 77GHzTransmitted power (dBm)12dBmModulation modeFMCWAntenna type2TX，4RXFOV angle (vertical) (°)30°FOV angle (horizontal) (°)150°Detection Range (m)12mSetup Function
table {
border-collapse: collapse;
width: 90%;
margin: 20px auto;
font-size: 14px;
}
th, td {
border: 1px solid #333;
padding: 8px;
vertical-align: top;
}
th {
background-color: #f5f5f5;
text-align: center;
}
.remark-img {
max-width: 200px;
height: auto;
margin-top: 8px;
}
Button pressing timeSetting functionLED bar showingDefinitionRemark0-1.5sVolume0OFFShortly press the setup button, the buzzer will beep once and enter into the volume adjustment mode, the display will show the current volume status. Each time you press the setup button, the volume will cycle, stop pressing, and the display will automatically save the status and exit. 1Low2Middle3High1.5s-3.0sImperial VS Metric displayF0MetricConstantly press the setup button, the buzzer will beep once and enter into the unit setting mode, the display will show the current status: Each time you press the setup button, F0 and F1 cycle, after stop pressing, and automatically save the status and exit. F1Imperial3.0s-4.5sObject typeC0All targetsConstantly press the setup key, the buzzer will beep once, and enter into the detection object setting mode, and the display will show the current status: Each time you press the setup key, the mode C0 and C1 cycle, after stop pressing, the display will automatically save the status and exit. C1Moving targets only4.5s-6sAutomatic learning functionL0OFFConstantly press the setup button, the buzzer will beep once, the display will enter into the automatic learning function setup mode, and the display will show the current status: Each time you press the setting button, the mode L0 and L1 cycle, after stop pressing, the display will enter the automatic learning mode, and the display automatically changes to L0 after the learning is completed. L1Sensor automatic learning>6.0sDetection ranged3.00.3m-4.2m distance is 0.05,0.10;0.10Constantly press the setup key, the buzzer will beep once, enter into the detection distance setting mode, and the display will show the distance current status: Each time you press the setting key, press d3.0, d4.5, d5.0, d6.0, d10 and dFF cycle, stop pressing and exit automatically. d4.54.5m-3.4m distance is 0.05,0.10;0.10d5.05.0m-4.0m distance is 0.05,0.10;0.10d6.06.0m-4.5m distance is 0.05,0.10;0.10d1010m-5.0m distance is 0.05,0.10;0.10dFFAdjust via CAN tool Wiring diagramWiring connectlonNote:1.If the trigger cable won't be used, please wrap thecable to avoid short circuit.2.The Trigger output is negative, the Max. input currentshould be no more than 500mA. Sensor Installation1. Installation height2. Requirements for vertical installation angle Installation heightUpward angle0.6-0.75m10°0.75-1.3m5°3. Sensor fixThe radar is installed on the vehicle body with a bracket, and the vertical installation angle is adjusted through the mounting bracket.Control boxinstallation1. In order to connect the cables easier, the control box is suggested to lay in the cabin.2. The control box should be sticked on the metal part of the vehicle. In order to fix thecontrol box firmly, before stick, please clean the surface. Function descrlptlon1.System self diagnosisAfter the system is powered on, it will start self diagnosis and show the self diagnosis result via display.2. Reversing warning function 2.1. Start conditionsa.IGNONb. The gear is in reverse 2.2 Reversing alarm a. The distance is showed according to the distance of the object, and the buzzer alarms according to this distance;b.The default alarm area of the system is shown in the figure below:c.The default alarm and distance segment of the system are shown in the following table:d. When the display is providing warning, the trigger will drive external equipment. 3.Detection range setting function The detection range of the radar is shown in the following figure. For different types of vehices and conditions,the radar can be used by PC-side configuration soffware, using CAN bus tools to configure the detection area.L1: The distance from the mounting position of' the sensor to the rear end of the vehicle (set range 0-2m, accurate to 0.1m).Default value: Om;L2: For the warning distance(set range from 1-30m, accurate to 0.1m),Default value:10.Om;W1: The detection width on the left side of the sensor (set range from 1m to 5m, accurate to0.1m),Default value:1.3m;W2: The detection width on the right side of the sensor (set range from 1m to 5m, accurate to0.1m),Default value:1.3m.4.Learning function Wh
Autostar 3rd generation microwave (77Ghz, 2TR & 4RX)blind spot detection is developed byhome R&D team.Based on accurate algorithm, with high detection accuracy, this latestgeneration BSD works greatly, and no false alarm. Compared to the 2nd generation sensor,the detection distance is even longer, it could reach 80m.Besides the great performance,the most outstanding feature is the easy installation method.
Autostar’s Backup radar sensor systems based on 77Ghz radar technology are specially designed to detect people, vehicles and objects in rear blind spots of commercial vehicle, effectively reducing accidents. They are able to detect stationary and moving objects, providing the driver with in-cab visual and audible warnings – alerting the operator whose attention can not be focused on all danger areas. Backup radar sensor works effectively in harsh and in poor visibility environments including darkness, heavy dust, smoke and fog.
Reversing system with RCTA/LAC/BSD/RCW
Auto Brake Reverse system
Bluetooth Wireless Reverse system
Turning manoeuvres involving collisions between trucks turning right and cyclists, typically occurring at lower driving speeds or standstill, usually have serious consequences for vulnerable road users(VRU). In the past, the safety of VRU was raised by an improvement of the truck driver’s vision by increasing the number of mirrors by equipping trucks with side under-run protection. Now, Autostar develop a completely new solution to solve this issue by 77Ghz radar sensor, which effectively improve VRU safety.
Forward Collision Warning (FCW)
UNECE R151 BSIS
Xiamen Autostar Electronics Co., Ltd
No.38, Xinglin North Road, Jimei District, Xiamen City,Fujian Province P. R. China